DG309DY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG309 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 15V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG309DY-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. There is an electrical component included in the 16 series. A SPST - NC switching circuit is used to build these analog multiplexers. A 4 circuit is present in this switch device. Try searching with DG309 if you're looking for variants. Internally, this switch multiplexer has a resistance of 100Ohm. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. An effective Dual, Single supply digital multiplexer. It is recommended to use 13V as the lowest voltage for the electrical part. This multiplexer would work with 10μA current. It may damage the digital multiplexer if the voltage is higher than 10μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. In the case of dual power supplies, you should connect at least 7V. 15V operating voltages can be used with this electrical part.
DG309DY-E3 Features
1 Channels
Switch Circuit: SPST - NC
10μA Supply Current
DG309DY-E3 Applications
There are a lot of Vishay Siliconix DG309DY-E3 Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- HDTV
- Transmit
- Voice over IP/DSL – Integrated Access Devices, Smart
- DSLAMs
- ATM
- Audio and video signal routing
- Communication systems
- PCMCIA cards
- Cable Modem
