Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
6-UFDFN |
Number of Pins |
6 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2014 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Resistance |
15Ohm |
Terminal Finish |
PALLADIUM GOLD OVER NICKEL |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
160mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.4mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG3157 |
Output |
SEPARATE OUTPUT |
Pin Count |
6 |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Max Supply Current |
1μA |
Turn On Delay Time |
25 ns |
Supply Type |
Single |
Turn-Off Delay Time |
21 ns |
-3db Bandwidth |
300MHz |
On-State Resistance (Max) |
15Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
57 dB |
Channel Capacitance (CS(off), CD(off)) |
7pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
25ns, 21ns |
Charge Injection |
7pC |
Channel-to-Channel Matching (ΔRon) |
800m Ω |
Crosstalk |
-64dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
50ns |
Switch-off Time-Max |
45ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG3157ADN-T1-E4 Overview
Presented in 6-UFDFN, this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 2:1. The operating temperature is extended to around -40°C~85°C TA. There are 6 terminations totally. The electronic part delivers high-quality output through its 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. The electronic part body is injected with 6 pins. A SPDT switching circuit is used to build these analog multiplexers. There are 1 circuits in this multiplexer. Try searching with DG3157 if you're looking for variants. A 15Ohm internal resistance characterizes this multiplexer. To find out what the functions of 6 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Single supply type digital switch with a low cost. 1.65V should be the lowest voltage fed to the electronic component. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG3157ADN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 300MHz
DG3157ADN-T1-E4 Applications
There are a lot of Vishay Siliconix DG3157ADN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Industrial
- Isolation
- Voice over IP/DSL – Integrated Access Devices, Smart
- Battery Powered Systems
- DSUs
- Cross Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Avionics
- SONET/SDH ADM
- Relay replacements