DG333ADJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 2.508989g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 75Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 890mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG333 |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 200μA |
| Power Dissipation | 890mW |
| Max Supply Current | 200μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 5V~40V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 3.81mm |
| Length | 26.92mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG333ADJ-E3 Overview
The electrical component comes in 20-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. In Through Hole, this analog switch is mounted. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. Total terminations are 20. Due to its 4 channels, the electrical component produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. A total of 20 pins are injected into the electrical part body. Circuits based on SPDT switching are used to construct these analog switch ics. Circuits number 1 make up this analogue multiplexer. DG333 can be used to search for analog multiplexer variants. There is 75Ohm internal resistance in this digital multiplexer. For functions related to 20 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 40V voltage to the switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. 5V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 200μA. If you put voltage higher than 200μA on the digital multiplexer, damage may occur. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. If you are using a dual power supply, you should attach at least 4V. 8 outputs are included in the analogue multiplexer.
DG333ADJ-E3 Features
4 Channels
Switch Circuit: SPDT
200μA Supply Current
DG333ADJ-E3 Applications
There are a lot of Vishay Siliconix DG333ADJ-E3 Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Residential Gateways, Home Gateway/Router
- Fault Tolerant Systems
- PCMCIA cards
- DSLAMs
- E1 Multiplexer
- Power routing
- Transmit
- Central office
- Cable Modem
