DG333ADQ-T1-E3

175ns, 145ns SPDT 45Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 250pA 15V 20-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG333ADQ-T1-E3
Package: 20-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 154
Description: 175ns, 145ns SPDT 45Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 250pA 15V 20-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mounting Type	Surface Mount
Package / Case	20-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	20
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	20
Resistance	45Ohm
Subcategory	Multiplexer or Switches
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.635mm
Output	SEPARATE OUTPUT
Number of Channels	4
Number of Circuits	1
Max Supply Voltage	40V
Min Supply Voltage	5V
Voltage - Supply, Single/Dual (±)	5V~40V ±4V~22V
Neg Supply Voltage-Nom (Vsup)	-15V
Max Dual Supply Voltage	22V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	4V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	8pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	175ns, 145ns
Charge Injection	10pC
Channel-to-Channel Matching (ΔRon)	2 Ω (Max)
Crosstalk	-80dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant

DG333ADQ-T1-E3 Overview

Shipping overseas is convenient due to the electrical component's packing in 20-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. In total, there have been 20 terminations. High-quality output is provided by the electronic component's 4 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. SPDT switching circuits are used in these analog switch ics. Circuits number 1 make up this analogue multiplexer. As far as internal resistance is concerned, it has 45Ohm. For details about the functions of 20 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 40V should not normally be supplied to the switches. There should be 5V voltage fed to the electrical part below 5V. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. When using dual power supplies, you should attach at least 4V. This analog switch ic utilizes SEPARATE OUTPUT output.