DG333ALDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 20 |
| Weight | 2.508989g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 890mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Terminal Pitch | 2.54mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 5V~40V ±4V~22V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 45Ohm |
| Height | 3.81mm |
| Length | 26.92mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG333ALDJ Overview
This electronic part is conveniently packaged in 20-DIP (0.300, 7.62mm), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. There are 20 terminations totally. There is an electrical component included in the 20 series. Multiplexers built on a SPDT switching circuit are built. A 1 circuit is present in this switch device. A 45Ohm internal resistance characterizes this multiplexer. You can find the functions of the 20 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage that should be fed to the electronic electronic part. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. When using dual power supplies, you should attach at least 4V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Resistivity from Drain to Source is 45Ohm for this electronic part.
DG333ALDJ Features
Switch Circuit: SPDT
Drain-to-Source resistance: 45Ohm
DG333ALDJ Applications
There are a lot of Vishay Siliconix DG333ALDJ Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Frame Relay Equipment
- Cell phones
- Channelized and Unchannelized DS3 applications
- Ultrasound
- Remote Powered Equipment
- Cellular phones
- FTTH
- Audio signal routing
- HDTV
