DG333ALDJ-E3
| Parameters | |
|---|---|
| Weight | 2.508989g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 75Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 890mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | DG333 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 5V~40V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 3.81mm |
| Length | 26.92mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
DG333ALDJ-E3 Overview
Packed in 20-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. The advanced packaging method Tube provides high reliability. The multiplexer is located in Through Hole. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. In total, there have been 20 terminations. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. The electronic part body is injected with 20 pins. SPDT switching circuits are used in these analog switch ics. 1 circuits are used in this analogue multiplexer. Try searching for DG333 variants of the analog switch ic. Analog switches have 75Ohm internal resistance. To find out what the functions of 20 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 40V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 5V. This multiplexer would work with 1μA current. A digital multiplexer may suffer damage if voltage is applied above 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. For dual power supplies, a voltage of at least 4V should be attached. This analog switch ic utilizes SEPARATE OUTPUT output.
DG333ALDJ-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG333ALDJ-E3 Applications
There are a lot of Vishay Siliconix DG333ALDJ-E3 Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- USB 1.1 signal switching circuits
- Audio and video routing
- High reliability control systems
- Cell phones
- Imaging
- Power routing
- SDH
- CSU
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
