DG333ALDW
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 800.987426mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Power Dissipation | 800mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 5V~40V ±4V~22V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 45Ohm |
| Height | 2.34mm |
| Length | 12.8mm |
| Width | 7.49mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG333ALDW Overview
Shipping overseas is convenient due to the electrical component's packing in 20-SOIC (0.295, 7.50mm Width). High reliability is ensured by the advanced packaging method Tube. In Surface Mount, you'll find this switch device. There is 2:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 20. The electronic part delivers high-quality output through its 4 channels. Electronic part bodies are injected with 20 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. It consists of 1 circuits. The internal resistance of this digital multiplexer is 45Ohm. For details about the functions of 20 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 40V. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage that should be fed to the electronic electronic part. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch's dual supply capability, its voltage should not exceed 22V. It is recommended that you attach at least 4V to your dual power supply. It has a Drain to Source resistance of 45Ohm ohms. A analog switch ics with 8 outputs is included.
DG333ALDW Features
4 Channels
Switch Circuit: SPDT
Drain-to-Source resistance: 45Ohm
DG333ALDW Applications
There are a lot of Vishay Siliconix DG333ALDW Analog Switches & Multiplexers ICs applications.
- ATM
- Voice over IP/DSL – Integrated Access Devices, Smart
- New designs requiring multiplexer functions
- Intelligent PBX
- PCMCIA cards
- Digital Cross-Connects
- Microprocessor controlled systems
- Avionics test equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay replacements
