Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-SOIC (0.295, 7.50mm Width) |
Number of Pins |
20 |
Weight |
800.987426mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2017 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
Resistance |
75Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
800mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG333 |
Pin Count |
20 |
Number of Outputs |
8 |
Qualification Status |
Not Qualified |
Number of Channels |
4 |
Number of Circuits |
1 |
Max Supply Voltage |
40V |
Min Supply Voltage |
5V |
Operating Supply Current |
200μA |
Power Dissipation |
800mW |
Max Supply Current |
1μA |
Turn On Delay Time |
175 ns |
Voltage - Supply, Single/Dual (±) |
5V~40V ±4V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
4V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
8pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω (Max) |
Crosstalk |
-80dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
2.34mm |
Length |
12.8mm |
Width |
7.49mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG333ALDW-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-SOIC (0.295, 7.50mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. There are 20 terminations totally. This electronic part offers high-quality output due to its 4 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. A total of 20 pins are injected into the body of the electronic part. A SPDT switching circuit is used to build these analog multiplexers. A 1 circuit is present in this switch device. Try searching with DG333 to find analog multiplexer variants. A 75Ohm internal resistance characterizes this multiplexer. Datasheets for 20 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 40V. The digital multiplexer has a low cost Dual, Single supply. 5V should be the lowest voltage fed to the electronic component. An operating current of 200μA would be sufficient for this switch device. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 22V. A dual power supply should have at least 4V voltage attached. 8 outputs are included in the analogue multiplexer.
DG333ALDW-E3 Features
4 Channels
Switch Circuit: SPDT
200μA Supply Current
DG333ALDW-E3 Applications
There are a lot of Vishay Siliconix DG333ALDW-E3 Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- PDH Multiplexers
- Isolation
- ATM
- Channelized and Unchannelized DS3 applications
- Low-Voltage
- Audio and video routing
- Cross Connects
- Residential Gateways, Home Gateway/Router
- Microprocessor controlled systems