DG333ALDW-T1-E3
| Parameters | |
|---|---|
| Number of Outputs | 8 |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 200μA |
| Power Dissipation | 800mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 5V~40V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 45Ohm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 75Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG333 |
DG333ALDW-T1-E3 Overview
Due to its 20-SOIC (0.295, 7.50mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 20. A electrical component with 4 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Unlike digital switches, these are based on SPDT switching circuits. 1 circuits are used in this analogue multiplexer. Use DG333 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 75Ohm. The datasheets for the 20 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 40V. The digital multiplexer has a low cost Dual, Single supply. There should be 5V voltage fed to the electrical part below 5V. For this multiplexer to operate, 1μA current would be sufficient. When the digital multiplexer is charged above 1μA, damage can occur. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 4V. There is 45Ohm resistance between the Drain and Source on this part. The analog switch ics includes 8 outputs.
DG333ALDW-T1-E3 Features
4 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 45Ohm
DG333ALDW-T1-E3 Applications
There are a lot of Vishay Siliconix DG333ALDW-T1-E3 Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Cross Connects
- Sample hold systems
- Cell phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- SDH/SONET multiplexers
- Frame Relay Equipment
- E1 Network Equipment
- ATM
- Signal routing between systems
