DG3516DB-T5-E1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFBGA |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 2.9Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 457mW |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG3516 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 457mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 51 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 45 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 2.9Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 54 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 12pF |
| On-state Resistance Match-Nom | 0.25Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 45ns, 42ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 250m Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 490μm |
| Length | 2.02mm |
| Width | 1.52mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG3516DB-T5-E1 Overview
The electronic component is convenient to ship overseas because it is packed in a 10-WFBGA. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. Totally, there are 10 terminations. A 1 channel electronic part produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. As part of its design, the 10 series is equipped with this electronic component. Based on SPDT switching circuits, these analog multiplexers work. Try searching with DG3516 if you're looking for variants. Internally, this switch multiplexer has a resistance of 2.9Ohm. Datasheets for functions of 10 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. An effective Single supply digital multiplexer. 1.8V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1μA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. There are 2 inputs to be operated. There are 4 outputs on the analogue multiplexer.
DG3516DB-T5-E1 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 300MHz
DG3516DB-T5-E1 Applications
There are a lot of Vishay Siliconix DG3516DB-T5-E1 Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Access Concentrators
- PBXs
- Automotive applications
- Communications systems
- Signal routing between systems
- Automatic test equipment
- Video switching
- Sample hold systems
- Microprocessor Controlled Analog Systems
