banner_page

DG3535DB-T1-E1

82ns, 73ns SPDT 400mOhm BOTTOM Analog Switches BREAK-BEFORE-MAKE 10 Pins 2nA 3V 10-WFBGA


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG3535DB-T1-E1
  • Package: 10-WFBGA
  • Datasheet: PDF
  • Stock: 947
  • Description: 82ns, 73ns SPDT 400mOhm BOTTOM Analog Switches BREAK-BEFORE-MAKE 10 Pins 2nA 3V 10-WFBGA(Kg)

Details

Tags

Parameters
Mounting Type Surface Mount
Package / Case 10-WFBGA
Surface Mount YES
Number of Pins 10
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2014
JESD-609 Code e1
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 10
Resistance 400mOhm
Terminal Finish Tin/Silver/Copper (Sn/Ag/Cu)
Additional Feature VIDEO APPLICATION
Subcategory Multiplexer or Switches
Max Power Dissipation 457mW
Technology CMOS
Terminal Position BOTTOM
Terminal Form BALL
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 3V
Terminal Pitch 0.5mm
Time@Peak Reflow Temperature-Max (s) 40
Output SEPARATE OUTPUT
Pin Count 10
Power Supplies 3V
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 6V
Min Supply Voltage 1.8V
Nominal Supply Current 1nA
Max Supply Current 1μA
Turn On Delay Time 82 ns
Supply Type Single
Turn-Off Delay Time 73 ns
On-State Resistance (Max) 400mOhm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 69 dB
Current - Leakage (IS(off)) (Max) 2nA
Channel Capacitance (CS(off), CD(off)) 145pF
On-state Resistance Match-Nom 0.05Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 82ns, 73ns
Charge Injection 21pC
Channel-to-Channel Matching (ΔRon) 50m Ω (Max)
Crosstalk -69dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 90ns
Switch-off Time-Max 78ns
Voltage - Supply, Single (V+) 2.7V~3.3V
Height Seated (Max) 0.753mm
Width 1.5mm
Radiation Hardening No
RoHS Status ROHS3 Compliant

DG3535DB-T1-E1 Overview


Due to its 10-WFBGA packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -40°C~85°C TA extended. There are 10 terminations totally. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. As part of its design, the 10 series is equipped with this electronic component. These analog multiplexers are built based on SPDT switching circuits. It consists of 2 circuits. A 400mOhm internal resistance characterizes this multiplexer. For details about the functions of 10 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 6V. The analog switch ic is of the Single supply type and is cost-effective. There should be 1.8V voltage fed to the electrical part below 1.8V. A voltage of 2.7V~3.3V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. There are SEPARATE OUTPUT outputs on this analog switch ic. Check out the electrical component's additional features, such as the following: VIDEO APPLICATION.

DG3535DB-T1-E1 Features


1 Channels
Switch Circuit: SPDT
Additional Features: VIDEO APPLICATION

DG3535DB-T1-E1 Applications


There are a lot of Vishay Siliconix DG3535DB-T1-E1 Analog Switches & Multiplexers ICs applications.

  • PCMCIA cards
  • Digital Cross-Connects
  • Industrial control systems
  • Ultrasound
  • Low-Voltage
  • Audio/video switches
  • Transmit
  • 65 V DACs
  • Microwave transmission systems
  • Avionics test equipment

Write a review

Note: HTML is not translated!
    Bad           Good