DG381ACJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG381A |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 500μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Length | 19.05mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG381ACJ+ Overview
Due to its 14-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. Mounted in Through Hole is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around 0°C~70°C TA. In total, there have been 14 terminations. High-quality output is provided by the electronic component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 14 series. SPST - NC switching circuits are used in these analog switch ics. This multiplexer is composed of 2 circuits. Look for analog switch ic variants by searching with DG381A. It has an internal resistance of 50Ohm. To find out what the 14 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 18V. The digital multiplexer has a low cost Dual, Single supply. 5V should be the lowest voltage fed to the electronic component. 230μA current would be enough for this multiplexer to operate. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 18V. The voltage should be at least 5V if you are using dual power supplies. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG381ACJ+ Features
1 Channels
Switch Circuit: SPST - NC
230μA Supply Current
DG381ACJ+ Applications
There are a lot of Maxim Integrated DG381ACJ+ Analog Switches & Multiplexers ICs applications.
- Communications systems
- Channelized and Unchannelized DS3 applications
- Cellular phones
- Audio signal routing
- Microprocessor controlled systems
- Channel Banks
- Audio and video switching
- Central office
- Automatic test equipment
- SONET/SDH ADM
