DG384BDJ-E3
| Parameters | |
|---|---|
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | DG384 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 1mA |
| Throw Configuration | DPST |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 130ns (Typ) |
| Charge Injection | 10pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 5.08mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
DG384BDJ-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature extended to -40°C~85°C TA. In total, there are 16 terminations. A electrical component with 1 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. Multiplexers built on a DPST - NO switching circuit are built. There are 2 circuits in this multiplexer. Using the DG384 search parameter, you can discover variants of the switch. A 50Ohm internal resistance characterizes this multiplexer. The datasheets for the 14 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Dual, Single supply type digital switch with a low cost. There should be 13V voltage fed to the electrical part below 13V. It would be sufficient to run this analogue multiplexer with 230μA current. A voltage higher than 1mA may cause damage to the switch multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. The voltage should be at least 7V if you are using dual power supplies. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 15V operating voltages are supported by the electronic component. A 4 input needs to be operated.
DG384BDJ-E3 Features
1 Channels
Switch Circuit: DPST - NO
230μA Supply Current
DG384BDJ-E3 Applications
There are a lot of Vishay Siliconix DG384BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Communication systems
- Cellular phones
- High reliability control systems
- Cable Modem
- Intelligent PBX
- Multi-Line E1 Interface Cards
- New designs requiring multiplexer functions
- Wireless Local Loop
- Avionics and Military Systems
- Relay Replacement
