DG387BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 50Ohm |
| Max Power Dissipation | 470mW |
| Reach Compliance Code | unknown |
| Base Part Number | DG387 |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Power Dissipation | 470mW |
| Max Supply Current | 1mA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 2 |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 130ns (Typ) |
| Charge Injection | 10pC |
| Crosstalk | -74dB @ 500kHz |
| Voltage - Supply, Dual (V±) | ±15V |
| RoHS Status | ROHS3 Compliant |
DG387BDJ-E3 Overview
Presented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature extended to -40°C~85°C TA. As part of its design, the 14 series is equipped with this electronic component. Based on SPDT switching circuits, these analog multiplexers work. It consists of 1 circuits. Use DG387 to search for variants of the digital switches. It has an internal resistance of 50Ohm. The datasheets for the 14 pins explain the functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 13V. It would be sufficient to run this analogue multiplexer with 230μA current. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. 15V operating voltages are supported by the electronic component. A 2 input needs to be operated.
DG387BDJ-E3 Features
Switch Circuit: SPDT
230μA Supply Current
DG387BDJ-E3 Applications
There are a lot of Vishay Siliconix DG387BDJ-E3 Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Cellular phones
- Automotive applications
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Precision data acquisition
- Video switching
- Mechanical reed relay replacement
- Remote Powered Equipment
- Fault Tolerant Systems
- Medical Instrumentation
