DG390AAK/883B
| Parameters | |
|---|---|
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 10V |
| Max Supply Current | 500μA |
| Turn On Delay Time | 300 ns |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
DG390AAK/883B Overview
Shipping overseas is convenient with the electronic component packed in 16-CDIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature extended to -55°C~125°C TA. A total of 16 terminations have been recorded. A 1 channel electronic part produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. SPDT switching circuits are used in these analog switch ics. There are 2 circuits in this switch device. This digital multiplexer has 50Ohm internal resistance. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 36V. It is recommended to use 10V as the lowest voltage for the electrical part. When the digital multiplexer is charged above 500μA, damage can occur. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. In the case of dual power supplies, you should connect at least 5V. A voltage of 15V can be used to operate the electronic component.
DG390AAK/883B Features
1 Channels
Switch Circuit: SPDT
DG390AAK/883B Applications
There are a lot of Maxim Integrated DG390AAK/883B Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Microprocessor controlled systems
- Central office
- Avionics and Military Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cross Connects
- Data Acquisition Systems
- E1 Multiplexer
- Industrial
- 65 V DACs
