DG390ACWE+
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG390A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 500μA |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG390ACWE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.295, 7.50mm Width). To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around 0°C~70°C TA. In total, there have been 16 terminations. A 1 channel electronic part produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. Electronic part bodies are injected with 16 pins. Circuits based on SPDT switching are used to construct these analog switch ics. There are 2 circuits in this switch device. Try searching with DG390A if you're looking for variants. In this multiplexer, the internal resistance is 50Ohm. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 18V to a switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 230μA current. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 18V. When using dual power supplies, you should attach at least 5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG390ACWE+ Features
1 Channels
Switch Circuit: SPDT
230μA Supply Current
DG390ACWE+ Applications
There are a lot of Maxim Integrated DG390ACWE+ Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- Access Concentrators
- Avionics
- Signal routing between systems
- Optical Applications
- Fiber In The Loop (FITL)
- Fiber to the Home
- Communication systems
- PDAs
- Channel Banks
