DG390BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | DG390 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 1mA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 130ns (Typ) |
| Charge Injection | 10pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG390BDJ-E3 Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Through Hole is this multiplexer. Multiplexer and demultiplexer circuits have a number 2:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Into the electrical component body are injected 16 pins. The analog switch ics are built using SPDT switching circuits. There are 2 circuits in this switch device. Try searching for the analog switch ic with DG390 if you are looking for variants. Internally, this switch multiplexer has a resistance of 50Ohm. You can find the functions of the 16 pins in the datasheets. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 36V to a switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 13V. This digital switch can be operated with a current of 230μA. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 7V should be attached. There are SEPARATE OUTPUT outputs on this analog switch ic. It can operate from 15V operating voltages. Operating the 4 inputs requires 4 inputs.
DG390BDJ-E3 Features
1 Channels
Switch Circuit: SPDT
230μA Supply Current
DG390BDJ-E3 Applications
There are a lot of Vishay Siliconix DG390BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Communication systems
- DVD-R
- Sample-and-hold systems
- Remote Powered Equipment
- Cellular phones
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cross Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Medical
- Communication systems
