DG401AK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 Class B |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NO |
| Height Seated (Max) | 5.08mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG401AK/883B Overview
Shipping overseas is convenient with the electronic component packed in 16-CDIP (0.300, 7.62mm). In order to provide high reliability, an advanced packaging method Tube is used. In Through Hole, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -55°C~125°C TA. 16 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of its design, the 16 series is equipped with this electronic component. The analog switch ics are built using SPST - NO switching circuits. The multiplexer consists of 2 circuits. As far as internal resistance is concerned, it has 30Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 30V. There should be 10V voltage fed to the electrical part below 10V. For this switch, a dual supply voltage is feasible, but it must not exceed 20VYou should attach at least 4.5V voltage if you are using dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG401AK/883B Features
1 Channels
Switch Circuit: SPST - NO
DG401AK/883B Applications
There are a lot of Maxim Integrated DG401AK/883B Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Frame Relay Equipment
- USB 1.1 signal switching circuits
- Communications systems
- High speed data transmission line cards
- Intelligent PBX
- FTTH
- PBX interfaces
- MP3 players
- Signal routing between systems
