DG401BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 2 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG401BDJ Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around -40°C~85°C TA. In total, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Internally, this switch multiplexer has a resistance of 45Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 13V. A voltage higher than 500μA may cause damage to the switch multiplexer. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. There are SEPARATE OUTPUT outputs on this analog switch ic. This electrical part is compatible with 15V operating voltages. It is possible to operate 2 inputs.
DG401BDJ Features
1 Channels
Switch Circuit: SPST - NO
DG401BDJ Applications
There are a lot of Vishay Siliconix DG401BDJ Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Cross Connects
- Power routing
- Medical
- Precision test equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Avionics
- Communication systems
- 65 V DACs
