Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Weight |
1.627801g |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2013 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
55Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
450mW |
Technology |
CMOS |
Number of Functions |
2 |
Supply Voltage |
15V |
Base Part Number |
DG401 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
15V |
Number of Channels |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
1mA |
Power Dissipation |
450mW |
Max Supply Current |
500μA |
Throw Configuration |
SPST |
Turn On Delay Time |
150 ns |
Number of Inputs |
2 |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
60pC |
Crosstalk |
-94.8dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Voltage - Supply, Dual (V±) |
±15V |
Height |
3.81mm |
Length |
21.33mm |
Width |
7.11mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG401BDJ-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around -40°C~85°C TA are extended for operation. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Use DG401 to search for variants of the digital switches. An switch multiplexer with 55Ohm internal resistance has a value of 55Ohm. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Dual, Single supply type digital switch with a low cost. It is recommended to use 13V as the lowest voltage for the electrical part. 1mA current would be enough for this multiplexer to operate. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It can operate from 15V operating voltages. In order to operate the 2 inputs, there are several steps to follow.
DG401BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NO
1mA Supply Current
DG401BDJ-E3 Applications
There are a lot of Vishay Siliconix DG401BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Modems
- SONET/SDH ADM
- Cell phones
- Industrial and process control systems
- Data switching
- Avionics test equipment
- SONET
- Channelized and Unchannelized DS3 applications
- Medical
- Video signal routing