DG401BDY-E3

150ns, 100ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE DG401 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG401BDY-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 985
Description: 150ns, 100ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE DG401 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2008
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	55Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG401
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	15V
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	1mA
Power Dissipation	600mW
Max Supply Current	500μA
Throw Configuration	SPST
Turn On Delay Time	150 ns
Number of Inputs	2
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	60pC
Crosstalk	-94.8dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NO
Voltage - Supply, Dual (V±)	±15V
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG401BDY-E3 Overview

This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. 16 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. Try searching for the analog switch ic with DG401 if you are looking for variants. A 55Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 36V. Dual, Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 13V. An operating current of 1mA would be sufficient for this switch device. If you put voltage higher than 500μA on the digital multiplexer, damage may occur. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIf you are using a dual power supply, you should attach at least 7V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 15V operating voltages are supported by the electronic component. The electrical component supports 2 inputs.