DG401CJ+
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG401 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Qualification Status | Not Qualified |
| Power Supplies | 5+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 45Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NO |
| Length | 19.175mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
DG401CJ+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. In total, 16 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 16 series is equipped with this electronic component. SPST - NO switching circuits are used in these analog switch ics. There are 2 circuits in this multiplexer. Try searching with DG401 if you're looking for variants. The analogue multiplexer in this example is a typical Multiplexer or Switches. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG401CJ+ Features
1 Channels
Switch Circuit: SPST - NO
DG401CJ+ Applications
There are a lot of Maxim Integrated DG401CJ+ Analog Switches & Multiplexers ICs applications.
- MP3 players
- Mechanical reed relay replacement
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- High speed data transmission line cards
- E1 Network Equipment
- Modems
- Audio signal routing
- Isolation
- Cross Connects
- Audio and video signal routing
