DG401DJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG401 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG401DJ Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There are 16 pins injected into the electronic part body. SPST - NO switching circuits are used in these analog switch ics. There are 2 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with DG401. As far as internal resistance is concerned, it has 45Ohm. For functions related to 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 20V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. It would be sufficient to run this analogue multiplexer with 10nA current. It may damage the digital multiplexer if the voltage is higher than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
DG401DJ Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
DG401DJ Applications
There are a lot of Maxim Integrated DG401DJ Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- DVD-R
- Fault Tolerant Systems
- Automatic test equipment
- Battery Powered Systems
- Avionics and Military Systems
- Optical Applications
- E1 Network Equipment
- T1/E1 Terminals
- Isolation
