DG401DY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 55Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG401 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Power Supplies | 5+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5μA |
| Throw Configuration | SPST |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
DG401DY-E3 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tube. Surface Mount is where this multiplexer is located. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. A total of 16 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 16 pins. Based on SPST - NO switching circuits, these analog multiplexers work. There are 2 circuits in this multiplexer. Using the DG401 search parameter, you can discover variants of the switch. An switch multiplexer with 55Ohm internal resistance has a value of 55Ohm. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 36V. Digital switch that provides Dual power at a cost-effective price. In order for the electronic part to function properly, the lowest voltage should be 13V. The switch device would be able to operate with 5μA current. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 7V voltage attached. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
DG401DY-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
DG401DY-E3 Applications
There are a lot of Vishay Siliconix DG401DY-E3 Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- Sample hold systems
- Fault Tolerant Systems
- Medical systems
- Microprocessor controlled systems
- SONET
- Intelligent PBX
- Imaging
- Ultrasound
- Video switching
