DG401DY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 55Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG401 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 25V |
| Operating Supply Current | 5μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
DG401DY-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. The multiplexer consists of 2 circuits. Try searching with DG401 if you're looking for variants. This digital multiplexer has 55Ohm internal resistance. Datasheets for functions of 16 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 44V to a switch device. An effective Dual, Single supply digital multiplexer. A low voltage of 25V should be applied to the electronic component. This multiplexer would work with 5μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG401DY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
DG401DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG401DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- SDH
- Private Branch Exchange (PBX)
- Access Concentrators
- DSUs
- Medical
- CSU
- Industrial control systems
- E1 Multiplexer
- PBXs
