DG403BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SPDT |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG403BDJ Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. 16 terminations have been made so far. A electrical component with 2 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. There is an electrical component included in the 16 series. Based on SPST - NO/NC switching circuits, these analog multiplexers work. Internally, this switch multiplexer has a resistance of 45Ohm. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 36V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. In order for the electronic part to function properly, the lowest voltage should be 13V. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. An analog IC with the number SPDT is integrated into this board. The electronic component can function from 15V. The analog switch ics includes 4 outputs.
DG403BDJ Features
2 Channels
Switch Circuit: SPST - NO/NC
DG403BDJ Applications
There are a lot of Vishay Siliconix DG403BDJ Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Modems
- Battery Powered Instruments
- Frame Relay Equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- MP3 players
- Audio signal routing
- Precision test equipment
- Wireless Local Loop
- Industrial and process control systems
