DG403BDJ-E3

150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG403BDJ-E3
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 676
Description: 150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2012
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	55Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	450mW
Technology	CMOS
Peak Reflow Temperature (Cel)	NOT SPECIFIED
Number of Functions	2
Supply Voltage	15V
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	NOT SPECIFIED
Base Part Number	DG403
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	44V
Min Supply Voltage	25V
Analog IC - Other Type	SPDT
Operating Supply Current	1mA
Max Supply Current	500μA
Throw Configuration	SPST
Turn On Delay Time	150 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	60pC
Crosstalk	-94.8dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Dual (V±)	±15V
Height	3.81mm
Length	21.33mm
Width	7.11mm
RoHS Status	ROHS3 Compliant

DG403BDJ-E3 Overview

Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An injection of 16 pins is performed into the body of the electrical component. On the other hand, analog switches can be constructed using SPST - NO/NC switching circuits. 4 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with DG403 if you are looking for variants. The internal resistance of this digital multiplexer is 55Ohm. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 44V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. A low voltage of 25V should be applied to the electronic component. An operating current of 1mA would be sufficient for this switch device. A voltage higher than 500μA may cause damage to the switch multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. If you are using dual power supplies, you should attach at least 7V. There is an integrated analog IC SPDT in the module. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.