DG403BDY
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SPDT |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
DG403BDY Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 16. A 2 channel electronic part produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. There are 16 pins injected into the electronic part body. Based on SPST - NO/NC switching circuits, these analog multiplexers work. It has an internal resistance of 45Ohm. Datasheets for 16 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 36V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 13V is the lowest voltage the electrical component should receive. If you put voltage higher than 500μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. You should attach at least 7V voltage if you are using dual power supply. It is integrated with SPDT analog ICs. The electrical part can be operated at 15V voltage levels. A analog switch ics with 4 outputs is included.
DG403BDY Features
2 Channels
Switch Circuit: SPST - NO/NC
DG403BDY Applications
There are a lot of Vishay Siliconix DG403BDY Analog Switches & Multiplexers ICs applications.
- PBXs
- Battery Powered Systems
- Data Acquisition Systems
- New designs requiring multiplexer functions
- Voice over IP/DSL – Integrated Access Devices, Smart
- Audio/video switches
- Audio and video switching
- Isolation
- PDH Multiplexers
- Cross Connects
