DG403BDY-E3

150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG403BDY-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 451
Description: 150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2013
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	55Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG403
Pin Count	16
Number of Outputs	4
Operating Supply Voltage	15V
Number of Channels	2
Max Supply Voltage	36V
Min Supply Voltage	13V
Analog IC - Other Type	SPDT
Operating Supply Current	1mA
Nominal Supply Current	250μA
Power Dissipation	600mW
Max Supply Current	500μA
Throw Configuration	SPST
Turn On Delay Time	150 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	60pC
Crosstalk	-94.8dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Dual (V±)	±15V
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG403BDY-E3 Overview

This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. The advanced packaging method Tube provides high reliability. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. This electronic part offers high-quality output due to its 2 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An injection of 16 pins is performed into the body of the electrical component. These analog multiplexers are built based on SPST - NO/NC switching circuits. Try searching for DG403 variants of the analog switch ic. In this multiplexer, the internal resistance is 55Ohm. To find out what the 16 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 36V. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 13V. For this multiplexer to operate, 1mA current would be sufficient. Putting voltage greater than 500μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. A SPDT analog IC is integrated into the board. The electronic component can function from 15V. 4 outputs are included in the analogue multiplexer.