DG403BDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SPDT |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG403BDY-T1 Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. As part of the design of the 16 series, this electronic part has been incorporated into the system. These analog multiplexers are built based on SPST - NO/NC switching circuits. This multiplexer is composed of 4 circuits. As far as internal resistance is concerned, it has 45Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 13V voltage fed to the electrical part below 13V. The analogue multiplexer may be damaged if voltage is greater than 500μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. The voltage should be at least 7V if you are using dual power supplies. It is integrated with SPDT analog ICs. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. It can operate from 15V operating voltages.
DG403BDY-T1 Features
1 Channels
Switch Circuit: SPST - NO/NC
DG403BDY-T1 Applications
There are a lot of Vishay Siliconix DG403BDY-T1 Analog Switches & Multiplexers ICs applications.
- PBXs
- Frame Relay Equipment
- SONET/SDH ADM
- PCMCIA cards
- Optical Applications
- Cable Modem
- Avionics and Military Systems
- Fault Tolerant Systems
- Industrial control systems
- Industrial and process control systems
