DG403BDY-T1-E3

150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG403BDY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 546
Description: 150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	55Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG403
Pin Count	16
Number of Outputs	4
Operating Supply Voltage	15V
Number of Channels	2
Max Supply Voltage	36V
Min Supply Voltage	13V
Analog IC - Other Type	SPDT
Operating Supply Current	1mA
Power Dissipation	600mW
Max Supply Current	500μA
Throw Configuration	SPST
Turn On Delay Time	150 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	60pC
Crosstalk	-94.8dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Dual (V±)	±15V
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG403BDY-T1-E3 Overview

Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~85°C TA. In total, 16 terminations have occurred. A 2 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 16 pins. Unlike digital switches, these are based on SPST - NO/NC switching circuits. Try searching with DG403 to find analog multiplexer variants. There is 55Ohm internal resistance in this digital multiplexer. For details about the functions of 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 36V to a switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 13V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 1mA. Putting voltage greater than 500μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. You should attach at least 7V voltage if you are using dual power supply. With a SPDT analog IC integrated into the board. 15V operating voltages can be used with this electrical part. 4 outputs are included in the analogue multiplexer.