DG403CJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | DG403 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG403CJ+ Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Increasing operating temperature to around 0°C~70°C TA. In total, there have been 16 terminations. A electrical component with 1 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. A SPDT switching circuit is used for these analog switches. There are 2 circuits in this switch device. Try searching for DG403 variants of the analog switch ic. The internal resistance of this digital multiplexer is 45Ohm. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 20V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 4.5V voltage fed to the electrical part below 4.5V. In order to operate this switch device, it would need a current of 10nA. Putting voltage greater than 1μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 20V. A dual power supply should have at least 4.5V voltage attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG403CJ+ Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG403CJ+ Applications
There are a lot of Maxim Integrated DG403CJ+ Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- DSUs
- Channelized and Unchannelized DS3 applications
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- SDH
- Battery Powered Instruments
- Private Branch Exchange (PBX)
- Precision data acquisition
- Mechanical reed relay replacement
- Relay replacements
