DG403DJ-E3

150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG403DJ-E3
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 938
Description: 150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Weight	1.627801g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	45Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	450mW
Technology	CMOS
Number of Functions	2
Supply Voltage	15V
Base Part Number	DG403
Pin Count	16
Number of Outputs	4
Operating Supply Voltage	12V
Polarity	Non-Inverting
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	30V
Min Supply Voltage	10V
Operating Supply Current	10nA
Nominal Supply Current	10nA
Power Dissipation	450mW
Max Supply Current	1μA
Throw Configuration	SPDT
Turn On Delay Time	150 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	30mA
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	10pC
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	30Ohm
Voltage - Supply, Dual (V±)	±15V
Height	4.45mm
Length	19.43mm
Width	7.87mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG403DJ-E3 Overview

This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. In total, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. A SPST - NO/NC switching circuit is used for these analog switches. A 2 circuit is present in this switch device. Try searching with DG403 if you're looking for variants. This digital multiplexer has 45Ohm internal resistance. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. 10V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 10nA. Put voltage above 1μA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. With dual power supplies, you should attach at least 4.5V. It can operate from 12V operating voltages. A Drain to Source resistance of 30Ohm is shown for this electronic part. The analog switch ics includes 4 outputs.