DG403DVZ
| Parameters | |
|---|---|
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | IT CAN ALSO OPERATE FROM 5V TO 34V SINGLE SUPPLY |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Operating Supply Voltage | 28V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPDT |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 17V |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Off-state Isolation-Nom | 72 dB |
| Neg Supply Voltage-Max (Vsup) | -20V |
| On-state Resistance Match-Nom | 3Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
DG403DVZ Overview
As the electronic part is packed in TSSOP, international shipping is convenient. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. There is 45Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 40V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 10nA current would suffice. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 17V. For dual power supplies, a voltage of at least 5V should be attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. The electrical part can be operated at 28V voltage levels. This electrical component also includes additional features such as IT CAN ALSO OPERATE FROM 5V TO 34V SINGLE SUPPLY. Temperatures above 85°C degrees Celsius should not be operated by the multiplexer.
DG403DVZ Features
1 Channels
10nA Supply Current
Additional Features: IT CAN ALSO OPERATE FROM 5V TO 34V SINGLE SUPPLY
DG403DVZ Applications
There are a lot of Intersil (Renesas Electronics America) DG403DVZ Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Audio/video switches
- Channelized and Unchannelized DS3 applications
- Audio signal routing
- Communications systems
- Private Branch Exchange (PBX)
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- High reliability control systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Mechanical reed relay replacement
