Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
45Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG403 |
Pin Count |
16 |
Polarity |
Non-Inverting |
Number of Channels |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Operating Supply Current |
10nA |
Max Supply Current |
1μA |
Turn On Delay Time |
150 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG403DY+ Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. As a result of its 2 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. The analog switch ics are built using SPDT switching circuits. Try searching for the analog switch ic with DG403 if you are looking for variants. It has an internal resistance of 45Ohm. The datasheets for the 16 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 30V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 10V. 10nA current would be enough for this multiplexer to operate. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V.
DG403DY+ Features
2 Channels
Switch Circuit: SPDT
10nA Supply Current
DG403DY+ Applications
There are a lot of Maxim Integrated DG403DY+ Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Automotive applications
- Microprocessor controlled systems
- Fiber In The Loop (FITL)
- Ultrasound
- PBX interfaces
- Precision instrumentation
- High reliability control systems
- Data Acquisition Systems
- Audio and video signal routing