DG403DY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Pin Count | 16 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPDT |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 5V~34V ±5V~17V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
DG403DY Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Tube provides high reliability. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 2 channels. An electrical component of this type can be found in the 16 series. The analog switch ics are built using SPST - NO/NC switching circuits. An switch multiplexer with 45Ohm internal resistance has a value of 45Ohm. Datasheets for functions of 16 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. 13V is the lowest voltage the electrical component should receive. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. Operating voltages range from 15V. It has a Drain to Source resistance of 35Ohm ohms. An output of 4 is provided by the digital multiplexer.
DG403DY Features
2 Channels
Switch Circuit: SPST - NO/NC
Drain-to-Source resistance: 35Ohm
DG403DY Applications
There are a lot of Vishay Siliconix DG403DY Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- E1 Network Equipment
- DSLAMs
- PBX interfaces
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- USB 1.1 signal switching circuits
- Medical
- PDH Multiplexers
- 65 V DACs
- Precision instrumentation
