DG403DY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SPDT |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 5V~34V ±5V~17V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG403DY-T1 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Extended operating temperature around -40°C~85°C TA. In total, there are 16 terminations. Into the electrical component body are injected 16 pins. Multiplexers built on a SPST - NO/NC switching circuit are built. The multiplexer consists of 2 circuits. The internal resistance of this digital multiplexer is 45Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. Analog switch ics with Dual, Single supply type are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. A dual power supply should have at least 7V voltage attached. This product is integrated with an analog integrated circuit (IC) of type SPDT. This analog switch ic utilizes SEPARATE OUTPUT output. 15V operating voltages are supported by the electronic component. It is possible to operate 4 inputs.
DG403DY-T1 Features
Switch Circuit: SPST - NO/NC
DG403DY-T1 Applications
There are a lot of Vishay Siliconix DG403DY-T1 Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Medical Instrumentation
- Low-Voltage
- High reliability control systems
- Relay replacements
- Precision instrumentation
- MP3 players
- Medical
- PCMCIA cards
- New designs requiring multiplexer functions
