DG403DY-T1-E3

150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG403DY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 247
Description: 150ns, 100ns SPST - NO/NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG403 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2008
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	55Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG403
Pin Count	16
Number of Outputs	4
Qualification Status	Not Qualified
Operating Supply Voltage	15V
Polarity	Non-Inverting
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	5μA
Nominal Supply Current	10nA
Power Dissipation	600mW
Max Supply Current	1μA
Throw Configuration	SPDT
Turn On Delay Time	150 ns
Voltage - Supply, Single/Dual (±)	5V~34V ±5V~17V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	7V
High Level Output Current	100mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	60pC
Channel-to-Channel Matching (ΔRon)	3 Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	35Ohm
Height	1.55mm
Length	10mm
Width	4mm
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG403DY-T1-E3 Overview

Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. There are 16 terminations totally. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. As part of its design, the 16 series is equipped with this electronic component. Unlike digital switches, these are based on SPST - NO/NC switching circuits. A total of 2 circuits make up this switch device. Try searching for DG403 variants of the analog switch ic. In this multiplexer, the internal resistance is 55Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 36V to a switch device. An effective Dual, Single supply digital multiplexer. 13V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 5μA current. A voltage higher than 1μA may cause damage to the switch multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. If you are using a dual power supply, you should attach at least 7V. The electronic component can function from 15V. Resistivity from Drain to Source is 35Ohm for this electronic part. 4 outputs are included in the analogue multiplexer.