DG403DYZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | IT CAN ALSO OPERATE FROM 5V TO 34V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16, 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Number of Bits | 2 |
| Throw Configuration | DPST, SPDT |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 17V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Off-state Isolation-Nom | 72 dB |
| On-state Resistance Match-Nom | 3Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG403DYZ-T Overview
Due to its SOIC packaging, the electronic part is convenient for international shipping. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A key feature of the 16, 16 series is the inclusion of this electronic part as part of its design. As far as internal resistance is concerned, it has 45Ohm. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 40V to the switch device in normal circumstances. A cost-effective Dual, Single supply type analogue multiplexer. There should be 5V voltage fed to the electrical part below 5V. It would be sufficient to run this analogue multiplexer with 10nA current. A voltage higher than 1μA may cause damage to the switch multiplexer. There is no problem with using dual supply voltage, but it should not exceed 17V. It is recommended that you attach at least 5V to your dual power supply. It can operate from 28V operating voltages. This electronic part has additional features, such as: IT CAN ALSO OPERATE FROM 5V TO 34V SINGLE SUPPLY. In an environment with a temperature higher than 85°C, the digital switches should not operate. 2-bit operation is possible.
DG403DYZ-T Features
1 Channels
10nA Supply Current
Additional Features: IT CAN ALSO OPERATE FROM 5V TO 34V SINGLE SUPPLY
2-Bit
DG403DYZ-T Applications
There are a lot of Intersil (Renesas Electronics America) DG403DYZ-T Analog Switches & Multiplexers ICs applications.
- FTTH
- Fiber In The Loop (FITL)
- Automotive applications
- MP3 players
- Digital cross connects (DSX-1)
- PDAs
- PBX interfaces
- Communication systems
- Battery-powered systems
- Industrial
