Parameters |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-WFQFN |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2014 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
100Ohm |
Max Power Dissipation |
525mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.4mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG4051 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
-1μA |
Nominal Supply Current |
50nA |
Power Dissipation |
525mW |
Max Supply Current |
1μA |
Propagation Delay |
172 ns |
Turn On Delay Time |
151 ns |
Logic Function |
Multiplexer |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
2.7V~12V ±2.5V~5V |
Supply Type |
Dual, Single |
Bandwidth |
330MHz |
Neg Supply Voltage-Nom (Vsup) |
-3V |
Turn-Off Delay Time |
138 ns |
Max Dual Supply Voltage |
5V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2.5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
67 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
3pF 12pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Time (Ton, Toff) (Max) |
108ns, 92ns |
Charge Injection |
0.25pC |
Channel-to-Channel Matching (ΔRon) |
3 Ω |
Crosstalk |
-67dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
750μm |
Length |
2.6mm |
Width |
1.8mm |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG4051AEN-T1-E4 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-WFQFN. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 8:1. Temperatures around -40°C~125°C TA are extended for operation. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 8 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 16 series. A total of 1 circuits make up this switch device. DG4051 can be used to search for analog multiplexer variants. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. Datasheets for functions of 16 pins are available. A voltage higher than 12V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. 2.7V is the lowest voltage that should be fed to the electronic electronic part. -1μA current would be enough for this multiplexer to operate. Put voltage above 1μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5V. With dual power supplies, you should attach at least 2.5V. A 8 input needs to be operated. A 330MHz-bandwidth can be used for data transfer.
DG4051AEN-T1-E4 Features
8 Channels
-1μA Supply Current
Bandwidth: 330MHz
DG4051AEN-T1-E4 Applications
There are a lot of Vishay Siliconix DG4051AEN-T1-E4 Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Relay Replacement
- Digital access cross connects
- Audio and video signal routing
- Low-Voltage
- PCMCIA cards
- Video signal routing
- New designs requiring multiplexer functions
- Relay replacements
- Fiber In The Loop (FITL)