DG4053AEN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG4053 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 2 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | -1μA |
| Power Dissipation | 525mW |
| Max Supply Current | 1μA |
| Propagation Delay | 172 ns |
| Turn On Delay Time | 151 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 6 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±2.5V~5V |
| Supply Type | Dual, Single |
| Bandwidth | 730MHz |
| Neg Supply Voltage-Nom (Vsup) | -3V |
| Turn-Off Delay Time | 138 ns |
| Max Dual Supply Voltage | 5V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.5V |
| Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 4pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 108ns, 92ns |
| Charge Injection | 0.25pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -67dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 119ns |
| Height | 750μm |
| Length | 2.6mm |
| Width | 1.8mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
DG4053AEN-T1-E4 Overview
Due to its 16-WFQFN packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Mounted in Surface Mount is this multiplexer. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~125°C TA is the extended operating temperature. There are 16 terminations totally. The electronic part delivers high-quality output through its 2 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. A total of 16 pins are injected into the electrical part body. The analog switch ics are built using SPDT switching circuits. Circuits number 3 make up this analogue multiplexer. Try searching for DG4053 variants of the analog switch ic. There is 100Ohm internal resistance in this digital multiplexer. Datasheets for 16 pin functions are available upon request. Multiplexers should not be powered above 12V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage fed to the electronic component should be 2.7V. For this digital switch to work, -1μA current would suffice. It may damage the digital multiplexer if the voltage is higher than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 5V. If you are using dual power supplies, you should attach at least 2.5V. Operating the 6 inputs requires 6 inputs. 730MHz bandwidths enable data to be transferred.
DG4053AEN-T1-E4 Features
2 Channels
Switch Circuit: SPDT
-1μA Supply Current
Bandwidth: 730MHz
DG4053AEN-T1-E4 Applications
There are a lot of Vishay Siliconix DG4053AEN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Switching Systems
- SONET
- RGB switches
- Sample hold systems
- Audio and video signal routing
- Low-Voltage
- Data Acquisition Systems
- Automatic test equipment
- Multiplexers
