DG4053AEQ-T1-E3
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-TSSOP |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 100Ohm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 450mW |
| Base Part Number | DG4053 |
| Number of Outputs | 3 |
| Number of Channels | 3 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | -1μA |
| Nominal Supply Current | 50nA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Propagation Delay | 172 ns |
| Turn On Delay Time | 151 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 6 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±2.5V~5V |
| Supply Type | Dual, Single |
| Bandwidth | 730MHz |
| Turn-Off Delay Time | 138 ns |
| Max Dual Supply Voltage | 5V |
| -3db Bandwidth | 730MHz |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 4pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 108ns, 92ns |
| Charge Injection | 0.25pC |
| Channel-to-Channel Matching (ΔRon) | 3Ohm |
| Crosstalk | -67dB @ 10MHz |
| Height | 920μm |
| Length | 5.07mm |
| Width | 4.4mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG4053AEQ-T1-E3 Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Extended operating temperature around -40°C~125°C TA. By its 3 channels, the electronic component provides high-quality output. SPDT switching circuits are used in these analog switch ics. A 3 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with DG4053. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. Datasheets for 16 pin functions are available upon request. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 2.7V voltage fed to the electrical part below 2.7V. The switch device would be able to operate with -1μA current. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 5V. In the case of dual power supplies, you should connect at least 2.5V. Operating 6 inputs is required. The data can be transferred over a wide range of bandwidths, called 730MHz bandwidths. A temperature above 125°C is not suitable for operation of the analogue multiplexer. The analogue multiplexer has 3 outputs. It is offered by suppliers in package 16-TSSOP.
DG4053AEQ-T1-E3 Features
3 Channels
Switch Circuit: SPDT
-1μA Supply Current
-3db Bandwidth: 730MHz
Bandwidth: 730MHz
DG4053AEQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG4053AEQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Imaging
- DVD-R
- PDH Multiplexers
- Fiber to the Home
- Cell phones
- Automotive applications
- Multi-Line E1 Interface Cards
- Battery Powered Instruments
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Private Branch Exchange (PBX)
