DG405AK
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Number of Functions | 2 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 900mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.94mm |
| Length | 19.56mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
DG405AK Overview
This electronic part is conveniently packaged in 16-CDIP (0.300, 7.62mm), making it easy to ship abroad. Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Through Hole position. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Increasing operating temperature to around -55°C~125°C TA. Total terminations are 16. There are 16 pins injected into the electronic part body. DPST - NO switching circuits are used in these analog switch ics. A 2 circuit is present in this switch device. In this multiplexer, the internal resistance is 35Ohm. To find out what the 16 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 13V is the lowest voltage the electrical component should receive. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 22VFor dual power supplies, a voltage of at least 7V should be attached. There are SEPARATE OUTPUT outputs on this analog switch ic. There is a voltage range of 15V operating voltages for the electrical part. A 4 input needs to be operated. There is 35Ohm Drain to Source resistance on this electronic part.
DG405AK Features
Switch Circuit: DPST - NO
Drain-to-Source resistance: 35Ohm
DG405AK Applications
There are a lot of Vishay Siliconix DG405AK Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fault Tolerant Systems
- Mechanical reed relay replacement
- Wireless Local Loop
- Isolation
- 65 V DACs
- Access Concentrators
- Audio signal routing
- Avionics and Military Systems
