DG405BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | DPST |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG405BDJ Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tube is used. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. In total, there are 16 terminations. As a result of its 2 channels, this electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. 16 pins are injected to the electronic part body. A SPST - NO switching circuit is used for these analog switches. It consists of 4 circuits. As far as internal resistance is concerned, it has 45Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. An effective Dual, Single supply digital multiplexer. The lowest voltage the electronic part should receive is 13V. The analogue multiplexer may be damaged if voltage is greater than 500μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 7V. A DPST analog IC is integrated into the board. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. A voltage of 15V can be used to operate the electronic component.
DG405BDJ Features
2 Channels
Switch Circuit: SPST - NO
DG405BDJ Applications
There are a lot of Vishay Siliconix DG405BDJ Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- Remote wireless modules
- High reliability control systems
- SDH/SONET multiplexers
- USB 1.1 signal switching circuits
- Signal routing between systems
- Automatic test equipment
- Wireless Local Loop
- Isolation
- Routers
