DG405BDY-E3

150ns, 100ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE DG405 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG405BDY-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 388
Description: 150ns, 100ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE DG405 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	55Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG405
Pin Count	16
Number of Outputs	4
Qualification Status	Not Qualified
Operating Supply Voltage	15V
Number of Channels	2
Max Supply Voltage	36V
Min Supply Voltage	13V
Analog IC - Other Type	DPST
Operating Supply Current	1mA
Power Dissipation	600mW
Max Supply Current	500μA
Throw Configuration	SPST
Turn On Delay Time	150 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	60pC
Crosstalk	-94.8dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NO
Voltage - Supply, Dual (V±)	±15V
Height	1.55mm
Length	10mm
Width	4mm
RoHS Status	ROHS3 Compliant

DG405BDY-E3 Overview

Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~85°C TA. In total, there are 16 terminations. A electrical component with 2 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. SPST - NO switching circuits are used in these analog switch ics. Try searching for the analog switch ic with DG405 if you are looking for variants. In this multiplexer, the internal resistance is 55Ohm. The datasheets for the 16 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 13V. This digital switch can be operated with a current of 1mA. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. A DPST analog IC is integrated into the board. A voltage of 15V can be used to operate the electronic component. An output of 4 is provided by the digital multiplexer.