DG405BDY-T1
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | DPST |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
DG405BDY-T1 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 2 channels. With a 15V voltage supply, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. Circuits number 4 make up this analogue multiplexer. It has an internal resistance of 45Ohm. The functions of 16 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 13V as the lowest voltage for the electrical part. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 7V. There is an integrated analog IC DPST in the module. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electronic component can function from 15V.
DG405BDY-T1 Features
2 Channels
Switch Circuit: SPST - NO
DG405BDY-T1 Applications
There are a lot of Vishay Siliconix DG405BDY-T1 Analog Switches & Multiplexers ICs applications.
- Transmit
- Video signal routing
- Imaging
- Precision test equipment
- Relay replacements
- Digital cross connects (DSX-1)
- Industrial and process control systems
- CSU
- Power routing
- Audio and video signal routing
