DG405CJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG405 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG405CJ Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tube is used to provide high reliability. In Through Hole, this analog switch is mounted. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. A total of 16 terminations have been recorded. As a result of its 1 channels, this electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. There is an electrical component included in the 16 series. Circuits based on DPST - NO switching are used to construct these analog switch ics. The multiplexer consists of 2 circuits. Try searching for DG405 variants of the analog switch ic. There is 45Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 20V volts for the multiplexer. The digital multiplexer has a low cost Dual, Single supply. 4.5V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10nA would be sufficient for this switch device. A voltage higher than 1μA may cause damage to the switch multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG405CJ Features
1 Channels
Switch Circuit: DPST - NO
10nA Supply Current
DG405CJ Applications
There are a lot of Maxim Integrated DG405CJ Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- E1 Network Equipment
- Transmit
- Channel Banks
- Audio signal routing
- Microprocessor controlled systems
- Data Acquisition Systems
- E1 Multiplexer
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Automatic test equipment
