DG405DJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Number of Functions | 2 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| RoHS Status | Non-RoHS Compliant |
DG405DJ Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have the same number of circuits 2:1. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 16. A total of 16 pins are injected into the body of the electronic part. Multiplexers built on a DPST - NO switching circuit are built. The circuits in this analogue multiplexer number 2. The internal resistance of this digital multiplexer is 45Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 36V to a switch device. An effective Dual, Single supply digital multiplexer. 13V is the lowest voltage the electrical component should receive. A digital multiplexer may suffer damage if voltage is applied above 1μA. Despite this switch's dual supply capability, its voltage should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic. The electrical part can be operated at 15V voltage levels. The 4 inputs need to be operated in order to work.
DG405DJ Features
Switch Circuit: DPST - NO
DG405DJ Applications
There are a lot of Vishay Siliconix DG405DJ Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Access Concentrators
- Precision data acquisition
- FTTH
- Switching Systems
- RGB switches
- Private Branch Exchange (PBX)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- PCMCIA cards
- Video signal routing
