Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2000 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
45Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
DG405 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Power Supplies |
5+-15V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
20V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
10nA |
Nominal Supply Current |
10nA |
Max Supply Current |
1μA |
Throw Configuration |
DPST |
Turn On Delay Time |
150 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
DPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
DG405DY Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Extended operating temperature around 0°C~70°C TA. Total terminations are 16. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is part of the design of the 16 series that this electronic component is included. Unlike digital switches, these are based on DPST - NO switching circuits. 2 circuits are used in this analogue multiplexer. Try searching with DG405 if you're looking for variants. As far as internal resistance is concerned, it has 45Ohm. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 20V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 4.5V should be applied to the electronic component. 10nA current would be enough for this multiplexer to operate. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG405DY Features
1 Channels
Switch Circuit: DPST - NO
10nA Supply Current
DG405DY Applications
There are a lot of Maxim Integrated DG405DY Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Digital access cross connects
- Medical systems
- Relay replacements
- Wireless Local Loop
- Battery Powered Systems
- Cellular phones
- DSUs
- High reliability control systems
- FTTH