Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2013 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
55Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG405 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
15V |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
5μA |
Nominal Supply Current |
10nA |
Power Dissipation |
600mW |
Max Supply Current |
1μA |
Throw Configuration |
DPST, SPDT |
Turn On Delay Time |
150 ns |
Number of Inputs |
4 |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
DPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
60pC |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Voltage - Supply, Dual (V±) |
±15V |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG405DY-E3 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 2:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. In total, 16 terminations have occurred. Due to its 2 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. This electronic part can be found in the 16 series. Circuits based on DPST - NO switching are used to construct these analog switch ics. It consists of 2 circuits. Try searching with DG405 to find analog multiplexer variants. A 55Ohm internal resistance characterizes this multiplexer. For details about the functions of 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 13V should be applied to the electronic component. The analogue multiplexer could operate on 5μA current. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A voltage of 15V can be used to operate the electronic component. The electrical component supports 4 inputs.
DG405DY-E3 Features
2 Channels
Switch Circuit: DPST - NO
5μA Supply Current
DG405DY-E3 Applications
There are a lot of Vishay Siliconix DG405DY-E3 Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cellular phones
- Wireless Local Loop
- Medical systems
- SONET
- Cell phones
- Automotive applications
- PDAs
- FTTH